Rust-Oleum 317927 RockSolid Wet Look Concrete Sealer, 1 Gal., Clear
ROCKSOLID wet look concrete sealer seals and protects concrete and masonry surfaces from the damaging effects of water, chemicals and UV light. The water-base, film-forming formula provides a protective barrier to keep water out, protect against stains and extend the life of your concrete while leaving a wet look, high-gloss finish.
Rust-Oleum 317928 RockSolid Natural Look Concrete Sealer, 1 Gal., Clear
ROCKSOLID natural look concrete sealer seals and protects concrete and masonry surfaces from the damaging effects of water, chemicals and UV light. The water-base, film-forming formula provides a protective barrier to keep water out, protect against stains and extend the life of your concrete while leaving a natural look, low-gloss finish.
Concrete sealer for interior floors water based acrylic sealer 5 Gallon (515)
Normal 0 false false false EN-US JA X-NONE UBQ Industries – Active Elements™ Advance Seal Water based acrylic sealer for interior concrete floors.Active Elements™ – Advance Seal is a water-reducible acrylic emulsion based on hard polymers with ultra-small particle size that gives the coating excellent substrate penetration and durability. The material has excellent UV stability and will not chalk or yellow. Advance Seal is the perfect solution for interior floors where depth of color and moderate gloss is desired. For added protection on high traffic floors, Advance Seal can be top coated with Active Elements – Protect & Shine to form a sacrificial barrier.Coverage – 100-200 square feet per gallon Coverage variations depend on concrete surface porosity and amount of material applied. Surface Preparation Concrete must be clean and free of dirt, dust, oil, grease, mold and mildew, and any other contaminants. Acid Stained concrete must be neutralized, thoroughly cleaned, and dry prior to sealing. Pigment stained concrete must be completely dry prior to sealing.Bare concrete and overlays must be open and porous to allow for sealer penetration. All new concrete should be allowed to cure for a minimum of 45 days, or until a pH reading of 10.5 or less is achieved. Concrete must be completely dry prior to sealer application. It is strongly recommended that a surface probe moisture meter be utilized to verify the surface is dry. After visually determining the concrete is dry, test a minimum of 10 different areas of the concrete with the moisture meter. Pay special attention to cracks, control joints, and slab edges. Application – Roller Stir well before use. Pour Active Elements – Advance Seal through a strainer prior to use. Apply by using a high quality 3/8” nap lint free roller cover, or 1/4” nap mohair roller cover (for smooth surfaces). Dip directly into a roller pan and distribute the material by rolling laterally and then up and down (crosshatch rolling). Roll the material into a wet edge, and avoid excessive back rolling. When applying 2 coats of sealer roll the second coat perpendicular to the first. Keep containers closed when not in use, unattended open material will form a skin on the surface. Application – Sprayer ( HVLP or Airless) Stir well before use. Pour Active Elements – Advance Seal through a strainer prior to use. Spray using an airless or HVLP spray system. When applying 2 coats, spray the second coat perpendicular to the first. Always use a chemical respirator when spraying with an airless or HVLP spray system. Keep containers closed when not in use, unattended open material will form a skin on the surface.Drying Time Dry to touch: 30 minutes Dry hard: 55 minutes Recoat: 2 hours Light Foot Traffic: 4 hours Full Cure: 72 hours The listed dry times are for 75 degree (F) temperatures and medium humidity. Low temperatures and/or high humidity will slow drying and curing time. Clean Up Tools can be cleaned with soap and water Performance % solids by weight – 31% (ASTM D2369) 60 degree gloss – 100% (ASTM D523) Pencil Hardness – 4B (ASTM D3363) Flexibility – Greater than 32% elongation (the maximum for ASTM D522) Impact Resistance – 40 inch-lbs (ASTM D2794) Abrasion Resistance – Wear index of 0.248, CS17 wheels, 1000g load (ASTM D4060) Chemical Resistance – 1 hour spot test (ASTM D1308) Water – No softening, blistering, flaking or discoloration Detergent– No softening, blistering, flaking or discoloration Dilute Base (pH13) – No softening, blistering, flaking or discoloration Dilute Acid (pH2) – Discoloration, but no softening, blistering or flaking Gasoline– No softening, blistering, flaking or discoloration Motor Oil– No softening, blistering, flaking or discoloration Red Wine– No softening, blistering, flaking or discoloration Ketchup – No softening, blistering, flaking or discoloration Mustard– Discoloration, but no softening, blistering or flaking *Performance testing conducted by an independent laboratory. Limitations· Interior use only· This product may only be used on fully cured concrete. · Not suitable for flooring that is exposed to harsh chemicals. · Air and substrate temperatures must be at least 40°F and rising. Storage and Shelf Life Do not allow to freeze. Shelf life of unopened product is approximately one year. Slip and Fall Precautions OSHA and the American Disabilities Act (ADA) have now set enforceable standards for slip-resistance on pedestrian surfaces. The current coefficient of friction required by ADA is .6 on level surfaces and .8 on ramps. UBQ Industries, LLC recommends the use of angular slip-resistant aggregate in all coatings or flooring systems that may be exposed to wet, oily or greasy conditions. It is the contractor and end users’ responsibility to provide a flooring system that meets current safety standards. UBQ Industries, LLC or its sales agents will not be responsible for injury incurred in a slip and fall accident.Moisture Vapor Emissions/Alkalinity Precautions All interior concrete floors not poured over an effective moisture vapor barrier/inhibitor are subject to possible moisture vapor transmission and related high levels of alkalinity that may lead to blistering and failure of the coating system. It is the coating applicator’s responsibility to conduct calcium chloride and relative humidity probe testing to determine if excessive levels of vapor emissions or alkalinity are present before applying any coatings.Warranty The Manufacturer and/or the Seller warrants that if any goods supplied prove defective in workmanship or material, that Manufacturer and/or Seller shall replace them or refund the purchase price. This warranty is made in lieu of any and all other warranties expressed or implied. Before application, the User shall determine the suitability of the product for his intended use and User assumes all risks and liabilities whatsoever in connection therewith. Under no circumstances shall the Manufacturer and/or Seller be liable for incidental, consequential or other damages for alleged negligence, breach of warranty, or strict liability arising out of use or handling of this product. The sole liability of Manufacturer and/or Seller for any claims arising out of the use or sale of the product shall be for the User’s purchase price. Any claim of defective product must be received in writing within one (1) year from date of shipment. DO NOT TAKE INTERNALLY. KEEP OUT OF REACH OF CHILDREN.
Concrete sealer interior floor sealer water based acrylic sealer 1 gallon
UBQ Industries – Active Elements™ Advance Seal – Interior Concrete Floor SealerWater based acrylic sealer for interior concrete floors • 1 GallonActive Elements™ – Advance Seal is a water-reducible acrylic emulsion based on hard polymers with ultra-small particle size that gives the coating excellent substrate penetration and durability. The material has excellent UV stability and will not chalk or yellow. Advance Seal is the perfect solution for interior floors where depth of color and moderate gloss is desired. For added protection on high traffic floors, Advance Seal can be top coated with Active Elements – Protect & Shine to form a sacrificial barrier.Coverage – 100-200 square feet per gallon Coverage variations depend on concrete surface porosity and amount of material applied. Surface Preparation Concrete must be clean and free of dirt, dust, oil, grease, mold and mildew, and any other contaminants. Acid Stained concrete must be neutralized, thoroughly cleaned, and dry prior to sealing. Pigment stained concrete must be completely dry prior to sealing.Bare concrete and overlays must be open and porous to allow for sealer penetration. All new concrete should be allowed to cure for a minimum of 45 days, or until a pH reading of 10.5 or less is achieved. Concrete must be completely dry prior to sealer application. It is strongly recommended that a surface probe moisture meter be utilized to verify the surface is dry. After visually determining the concrete is dry, test a minimum of 10 different areas of the concrete with the moisture meter. Pay special attention to cracks, control joints, and slab edges. Application – Roller Stir well before use. Pour Active Elements – Advance Seal through a strainer prior to use. Apply by using a high quality 3/8” nap lint free roller cover, or 1/4” nap mohair roller cover (for smooth surfaces). Dip directly into a roller pan and distribute the material by rolling laterally and then up and down (crosshatch rolling). Roll the material into a wet edge, and avoid excessive back rolling. When applying 2 coats of sealer roll the second coat perpendicular to the first. Keep containers closed when not in use, unattended open material will form a skin on the surface.Application – Sprayer ( HVLP or Airless) Stir well before use. Pour Active Elements – Advance Seal through a strainer prior to use. Spray using an airless or HVLP spray system. When applying 2 coats, spray the second coat perpendicular to the first. Always use a chemical respirator when spraying with an airless or HVLP spray system. Keep containers closed when not in use, unattended open material will form a skin on the surface.Drying Time Dry to touch: 30 minutes Dry hard: 55 minutes Recoat: 2 hours Light Foot Traffic: 4 hours Full Cure: 72 hours The listed dry times are for 75 degree (F) temperatures and medium humidity. Low temperatures and/or high humidity will slow drying and curing time. Clean Up Tools can be cleaned with soap and waterPerformance % solids by weight – 31% (ASTM D2369) 60 degree gloss – 100% (ASTM D523) Pencil Hardness – 4B (ASTM D3363) Flexibility – Greater than 32% elongation (the maximum for ASTM D522) Impact Resistance – 40 inch-lbs (ASTM D2794) Abrasion Resistance – Wear index of 0.248, CS17 wheels, 1000g load (ASTM D4060) Chemical Resistance – 1 hour spot test (ASTM D1308) Water – No softening, blistering, flaking or discoloration Detergent– No softening, blistering, flaking or discoloration Dilute Base (pH13) – No softening, blistering, flaking or discoloration Dilute Acid (pH2) – Discoloration, but no softening, blistering or flaking Gasoline– No softening, blistering, flaking or discoloration Motor Oil– No softening, blistering, flaking or discoloration Red Wine– No softening, blistering, flaking or discoloration Ketchup – No softening, blistering, flaking or discoloration Mustard– Discoloration, but no softening, blistering or flaking *Performance testing conducted by an independent laboratory. Limitations· Interior use only· This product may only be used on fully cured concrete. · Not suitable for flooring that is exposed to harsh chemicals. · Air and substrate temperatures must be at least 40°F and rising.Storage and Shelf Life Do not allow to freeze. Shelf life of unopened product is approximately one year. Slip and Fall Precautions OSHA and the American Disabilities Act (ADA) have now set enforceable standards for slip-resistance on pedestrian surfaces. The current coefficient of friction required by ADA is .6 on level surfaces and .8 on ramps. UBQ Industries, LLC recommends the use of angular slip-resistant aggregate in all coatings or flooring systems that may be exposed to wet, oily or greasy conditions. It is the contractor and end users’ responsibility to provide a flooring system that meets current safety standards. UBQ Industries, LLC or its sales agents will not be responsible for injury incurred in a slip and fall accident.Moisture Vapor Emissions/Alkalinity Precautions All interior concrete floors not poured over an effective moisture vapor barrier/inhibitor are subject to possible moisture vapor transmission and related high levels of alkalinity that may lead to blistering and failure of the coating system. It is the coating applicator’s responsibility to conduct calcium chloride and relative humidity probe testing to determine if excessive levels of vapor emissions or alkalinity are present before applying any coatings.Warranty The Manufacturer and/or the Seller warrants that if any goods supplied prove defective in workmanship or material, that Manufacturer and/or Seller shall replace them or refund the purchase price. This warranty is made in lieu of any and all other warranties expressed or implied. Before application, the User shall determine the suitability of the product for his intended use and User assumes all risks and liabilities whatsoever in connection therewith. Under no circumstances shall the Manufacturer and/or Seller be liable for incidental, consequential or other damages for alleged negligence, breach of warranty, or strict liability arising out of use or handling of this product. The sole liability of Manufacturer and/or Seller for any claims arising out of the use or sale of the product shall be for the User’s purchase price. Any claim of defective product must be received in writing within one (1) year from date of shipment. DO NOT TAKE INTERNALLY. KEEP OUT OF REACH OF CHILDREN.
Concrete sealer clear wet look solvent based exterior garage floors 5 Gallon
UBQ Industries – Active Elements™ True Seal 400SSolvent Based Exterior Concrete Sealer – 400VOC – 5 gallon pail*****NOT available in California and Maricopa County, AZ******Active Elements TM – TrueSeal 400S is a high-quality, 400 VOC, solvent based sealer designed for decorative concrete projects. It is a tough acrylic methacrylate blended polymer that produces coatings with excellent gloss, stain-resistance and is easy to clean. Adhesion to properly prepared concrete surfaces is excellent and the material is non-yellowing. Active Elements – Solvent Seal 400S is fortified with a dual functioning HALS + UV absorber additive for maximum color protection. For next level protection from salt, chlorine and chemical attack; TrueSeal 400S contains a multifunctional silane additive to reject chemical attack and promote adhesion and cross-linking.Coverage 100-200 square feet per gallon – Coverage variations depend on concrete surface porosity and amount of material applied.Drying Time Dry to touch: 15-40 minutes Re-coat: 30-40 minutes Light Foot Traffic: 3 hours Heavy Traffic: 48-72 hours Dry times are for 75 degree (F) temperatures and medium humidity, lower temperatures will slow drying and curing time. Do not apply if rain is expected within 3 – 6 hours.Surface Preparation Concrete must be clean and free of dirt, dust, oil, grease, mold and mildew, and any other contaminants. Use our Degrease or Paint Strip for help with this.Acid stained concrete must be neutralized, thoroughly cleaned, and dry prior to sealing. Use our neutralize to help with this step. Pigment stained concrete must be completely cured prior to sealing.All new concrete should be allowed to cure for a minimum of 28-45 days, or until a pH reading of 10.5 or less is achieved. Concrete must be completely dry prior to sealer application. It is strongly recommended that a surface probe moisture meter be utilized to verify the surface is dry. After visually determining the concrete is dry, test a minimum of 10 different areas of the concrete with the moisture meter. Pay special attention to cracks, control joints, and slab edges. Application Tools Pump sprayer, Airless sprayer or Roller & Brush Thinning Scratch Coat – When applying to bare concrete, apply a “scratch coat” consisting of 1 part TrueSeal 400S & 1 part TrueSeal Thinner to ensure deep penetration and reduction of bubbling due to out-gassing. TrueSeal Thinner can be used to prepare the material for spray application. Add 1-2 quarts of TrueSeal Thinner per 1 gallon of sealer, based on thickness of coating desired.Preferred Method – Spraying When spraying, protect surroundings with masking paper, masking plastic, or spray shield. Always use a filter when pouring TrueSeal 400S into a sprayer. Use only high quality industrial grade solvent resistant spray equipment. Concrete surface temperature must be between 50 – 90 degrees (F). If rolling TrueSeal 400S, work material into a wet edge, and avoid excessive back rolling. When applying two coats, roll the second coat perpendicular to the first.Clean Up Tools can be cleaned with TrueSeal Thinner.Storage and Shelf Life Do not allow to freeze. Shelf life of unopened product is approximately one year. Keep away from heat, sparks & flame. Vapors may cause fire. Safety Always use appropriate safety equipment including but not limited to, goggles, face shield, rubber gloves, chemical resistant clothing or apron, and chemical respirator. For exterior use only. INHALATION: Vapors may cause dizziness, headaches, or nausea. Immediately move to fresh air. Seek medical attention. EYES: Contact with eyes can cause severe burning, irritation, and blurred vision. Flush with water. Seek medical attention. SKIN: May cause severe irritation and or chemical burns. Wash with soap and water. Seek medical attention. Keep out of reach of children.Use only with adequate ventilation.Keep away from heat, sparks & flame. Vapors may cause fire. Avoid prolonged contact with skin. Use only with adequate ventilation. Avoid breathing vapors or spray mist. Do not take internally. If swallowed, do not induce vomiting. Call physician immediately. Close container after use. It is the sole responsibility of the property owner or applicator to determine the suitability and safety of applying this product in areas of pedestrian traffic. LimitationsThis product may only be used on fully cured concrete. Allow a minimum of 28-45 days of cure time after the concrete is poured to allow ample time for the concrete to completely hydrate.Do not apply when air or surface temperature exceeds 90 degrees (F) or LAP marking / poor penetration / bubbling may result. Do not apply to wet or damp concrete, moisture will inhibit penetration of the sealer and cause improper curing, flaking or lifting of the sealer. Do not apply when it may rain, or if dew may condense on the surface before the sealer has cured. Allow for extended dry times during cold weather / high humidity. ProhibitionsSelected state and county jurisdictions prohibit or limit the use of solvent based products. Users should consult local guidelines before using this product.Slip and Fall PrecautionsOSHA and the American Disabilities Act (ADA) have standards for slip-resistance on pedestrian surfaces. The coefficient of friction required by ADA is .6 on level surfaces and .8 on ramps. UBQ Industries, LLC recommends the use of slip-resistant additives in all sealers or coatings that may be exposed to wet, oily or greasy conditions. It is the installer and end users’ responsibility to provide a flooring system that meets current safety standards. UBQ Industries, LLC or its sales agents will not be responsible for injury incurred in a slip and fall accident. WarrantyThis warranty is made in lieu of all other warranties, either expressed or implied. Before application the User shall determine the suitability of the product for his/her intended use and User assumes all risks and liabilities whatsoever in connection therewith. Neither seller nor manufacturer has any knowledge or control concerning the purchaser’s use of this product and no warranty is made as to the results of any use. The Manufacturer and/or Seller warrants that if any goods supplied prove defective in material the sole obligation shall be to replace said product. Any claim of defective product must be received in writing within one (1) year from date of shipment. Neither Manufacturer nor Seller shall assume any liability for injury, loss, or damage resulting from use of this product. DO NOT TAKE INTERNALLY. KEEP OUT OF REACH OF CHILDREN.
Rust-Oleum Moisture Stop Concrete Sealer 1 Gallon Model 301239 MPN 301239, 337
Brand New