25 Feet Cho-Seal EMI Shield Gasket Material, .062″ x .100″ Conductive Elastomer
2488XF1C.13 New Chomerics (by Parker Hannifin) Cho-Seal EMI Shield Gasket Material, .062″ x .100″ Conductive Elastomer, Part Number 10-05-4699-1285. Each bid quantity is for One (1) Bag Containing Twenty-Five (25) Linear Feet. You may bid / buy any number of bags, up to the total quantity available above. This was purchased at an electronics supplier liquidation earlier this year, and it was brand new on the original factory spools. We measured it and repackaged in heavy Ziplok bags for resale. Chomerics 1285 is made with a silicone rubber elastomer that is impregnated with finely powdered Silver and Aluminum metal during the manufacturing process. This gives it some interesting properties, such as conducting electricity and providing shielding against electromagnetic interference. It is noticeably heavier than ordinary silicone rubber, but it is not as stretchy. Hardness is around Shore 65 (+/-7). Parker has full specs for this product available online at: http://www.chomerics.com/products/emi/gaskets/cond_elast/specs/tables/1285.html Note: About 95% of these bags should be one full, unbroken 25′ piece of material. We did, however, have a few bags with broken pieces that got mixed in with the others (about 15 out of 300 bags). We will try to pull out any bags with “extra ends” as we ship them, but one could occasionally get through. According to the calipers Length: 25 Linear Feet Cross section: .100″ / 2.54mm x .062″ / 1.58mm (rectangular)
100 Chomeric EMI Shield Silicone Patch Dot Nickel Carbon Fiber 19-11-19907-S6305
2984XH3E.03 New Parker Chomerics Cho-Seal EMI (Electro-Magnetic Interference) Die Cut Shield Patch Dots, Made of Nickel Plated Carbon (Ni/C) Fiber Shielding Matrix, Part Number 19-11-19907-S6305. Each bid quantity is for a Lot of One Hundred (100) EMI Patch Dots. You may bid / buy any number of lots, up to the total quantity available above. These were purchased at an industrial liquidation earlier this year, and they were in the original factory bags. We packaged them in heavy Ziplok bags for resale. They seem to be some kind of peel-and-stick dots. However, the white side does not peel off very easily – if at all. On most pieces we tested, it is *very* firmly attached, and when it does finally tear, it shreds into fibers sort of like Tyvek. The silicone is soft and pliable, but the adhesive is probably out of date (August 2005). We therefore recommend that you simply dab on a suitable liquid adhesive, and bond the EMI patch to your surface. Should be just the thing for screw holes and other small EMI leaks. The part number 19-11-19907-S6305 breaks down as follows: 19-11: Die cut product 19907: Parker internal drawing number S6305: Material Ni/C (Nickel plated carbon fiber) According to the calipers: Diameter: .379″ / 9.64 mm Thickness (including white backing): .029″ / 0.74 mm Thickness (including white backing): .024″ / 0.61 mm According to the manufacturer: S6305 — Good performance in moderately corrosive environments; material of choice for flange finishes needing “bite-through” for good electrical contact. Molded (M) or Extruded (E) — M/E Conductive Filler — Ni/C Elastomer Binder — Silicone Type (Ref. MIL-DTL-83528) — Not Applicable Volume Resistivity, ohm-cm, max., as supplied without pressure sensitive adhesive CEPS-0002 C(Q/C) 0.100 MIL-DTL-83528 (Q/C) Not Applicable Hardness, Shore A ASTM D2240 (Q/C) 65 ± 10 Specific Gravity ASTM D792 (Q/C) 2.00 ± 0.25 Tensile Strength, psi (MPa), min. ASTM D412 (Q/C) 200 (1.38) Elongation, % min. or % min./max. ASTM D412 (Q/C) 100 Tear Strength, lb/in. (kN/m), min. ASTM D624 (Q) 50 (8.75) Compression Set, 70 hrs at 100°C,% max. A ASTM D395, Method B (Q) 30 Thermal Low Temperature Flex TR10, °C, min. ASTM D1329 (Q) -45 Maximum Continuous Use Temperature, °C B — 150 Thermal Conductivity, W/m-K (Typical) 300 psi (2.07 MPa) ASTM D5470 0.8 Electrical Shielding Effectiveness, dB, min. F Method 1: CHO-TM-TP08 C(Q) Method 2: MIL-DTL-83528 Para.4.6.12 (Q) Method 3: CHO-TM-TP09 C (Q) Method 1 200 kHz (H Field) Not Tested 100 MHz (E Field) 100 500 MHz (E Field) 100 2 GHz (Plane Wave) 100 10 GHz (Plane Wave) 100 40 GHz (Plane Wave) 75 Electrical Stability, ohm-cm, max. Heat Aging CEPS-0002 C (Q) 0.250(E) MIL-DTL-83528 Para 4.6.15 (Q/C) Not Applicable Resistance During Vibration MIL-DTL-83528 Para 4.6.13 (Q) Not Applicable Resistance After Vibration MIL-DTL-83528 Para 4.6.13 (Q) Not Applicable Post Tensile Set Volume Resistivity MIL-DTL-83528 Para 4.6.9 (Q/C) Not Applicable Regulatory EMP Survivability, kA per in. perimeter MIL-DTL-83528 Para 4.6.16 (Q) Not Applicable RoHS Compliant — Yes UL 94 Flammability Rating — HB We used to have a link to the manufacturer’s site providing additional information, however, eBay made us remove it. The noose slowly tightens…
Copper Foil EMI Shield Tape Guitar Conductive Adhesive 2x33ft
High quality copper foil tape designed for EMI shielding, electrical repairs, and grounding applications. Copper Foil Tape with Conductive Adhesive 2in x 33ft. Strong Conductive Adhesive. 1 × Copper Foil Conductive Tape Roll.
1.25″x2″ GOLD OVAL THANK YOU STICKERS LABELS Lot of 100 – Made in the USA
Track Page Views With Auctiva’s FREE Counter
5 Pieces 1/8″ X 1/2″ ALUMINUM 6061 T6511 FLAT BAR 14″ long Extruded Mill Stock
You are buying 5 pieces of 1/8″ X 1/2″ 6061 T6511 Aluminum extruded flat bar 14″ long +.07″/-0 A total of 70″. CHECK MY STORE FOR MORE SELECTIONS! FOR MORE ITEMS. CLICK ON MY STORES ICON .() We carry different sizes and types of ALUMINUM, BRASS, TAPS, DRILLS, END MILLS, CUTTERS, INSERTS and MORE. We sell only High Quality Industrial Tools. All Items are in stock and ready to ship! Returns will be accepted within 14 day after item is shipped to you, buyer will pay shipping unless the item was not as described in the listing or has a defect. If item was not as described or defective you will get a full refund upon item return. If item is returned for another reason that is not my mistake, I will refund the cost of the item minis any ebay selling fees only. The buyer will pay shipping and selling fees. This is extruded bar not sanded or polished and may have scratches from handling.
5 Pieces 1-1/8″ ALUMINUM 6061 ROUND ROD 12″ long Solid T6511 Extruded BAR STOCK
This is extruded bar not sanded or polished and may have scratches from handling.